Current Category
Gearbox parts > Gearbox accessories/gearchange

	Mini rodchange dust cover boot (stops dirt getting inside the gearchange unit) 21A425- Mini rodchange dust cover boot (stops dirt getting inside the gearchange unit) This is the boot that stops the dirt/dust from entering the gearchange unit on a rodchange gearchange setup!		Price:	QTY:

	Remote gearchange dust cover (large plug) 22A271- Remote gearchange dust cover (large plug) This the large plug that attaches to the side of the remote gearchange. This plug stops dirt/dust from entering the gearchange.		Price:	QTY:

	Mini reverse lock out, stops being able to select reverse gear on remote gearboxes MS71- REVERSE LOCK OUT (GEARLOCK) FOR REMOTE G/BOX (NOT RODCHANGE) Reverse gear lockout for remote type gearlevers to remove possibility of going into reverse in error.		Price:	QTY:

	Mini remote gearchange plug, (stops water from entering gearchange)- 22A285 22A285- REMOTE CONTROL EXTENSION 1/2 MOON PLUG Fitted in the gearbox remote control this half moon seal butted up against the gearbox remote housing.		Price:	QTY:

	Gearchange/rear exhaust mount GEX7251- GEARCHANGE/EXHAUST MOUNT This mount fits on Leyland mini/moke gear change and rear exhaust mounts on cooper S/other Mini.		Price:	QTY:

	Gearchange mount (remote type) 21A956 This is the mount at the very rear of the gear-change on remote gear-change (not rod or 850)		Price:	QTY:

	Mini rodchange gearbox roll pin RPS1416- Mini Rod change gearbox Roll pin. This pin can wear and cause gear selection problems, this is quite a comman problem on rod change gearboxes.		Price:	QTY:

	Mini remote gearchange lower plastic bush AYA3057- Mini 'remote only' gearchange lower plastic bush This is normally what causes the remote gearchange to viabrate, this is a replacement plastic bush for the bottom of the gearchange.		Price:	QTY:

	Mini rod change gear lever bias barrel MSG12- GEARBOX BIAS BARREL SLICKSHIFT Bias spring arrangement fits the shift rod on rod change cars to "bias" the shift lever towards the 3rd/4th gear gate.		Price:	QTY:

	Mini rod change selector sleeve- Genuine rover 42H1116- Mini rod change selector sleeve (GENUINE ROVER) This is the little selector sleeve that connects the gearchange to the gearbox, on ROD change cars 1974 on. Now only available from genuine rover		Price:	QTY:

	Mini rod change, gear lever extension rod eye 22G2792- Rod change extension rod eye This little extension rod is quite a light alloy, and they have a tendancy to wear, when these wear the gearchange becomes very sloppy- a good idea to get rid of any slop in your gearchange.		Price:	QTY:

	Mini diff housing bush for rodchange support bar 13H7286- Mini diff housing support rod bush (suits ROD change) This bush inserts into the rear of the diff housing, it only suits rod change cars from about 74on (it has two rods instead of the big alloy support gearchange)		Price:	QTY:

	Mini gearchange boot lock down ring (remote) 14A9942- GAITER RING FOR REMOTE CHANGE Metal retaining band, suits remote gearchange. Fit and finish is excellent. We think they're a pretty good replica!		Price:	QTY:

	Mini gearchange boot (heavy duty) fits all models AYG3175 - 22A608 Mini gearchange boot, these are the heavy duty thick rubber type, do not be fooled as there are cheaper variants available but they will last only 1/4 of the time as one of these (due to the tickness of the rubber).		Price:	QTY:

	Mini upper gear stick boot (suit wand type- 850) 14A6860- GEAR LEVER GAITER MAGIC WAND TYPE The first Minis had a very simple gear-change; the lever exits the transmission directly thru the floor, well forward. This requires a special boot to accommodate the curves in the floor and tunnel, and being rubber it eventually cracks with age and flexing. Replace it with the real thing to keep wet or dry road crud out of the car! As fitted to 850/some budget vans etc.		Price:	QTY:

[1] 2 Next Page