Minisport
|
Minisport |
 
|
AUE811- Mini SU 1-/2" carby gasket set This is most gaskets you will need to seal up that leaking S.U. of yours. Price:
Mini SU carby overhaul kit, suits 1&1/4! What you get: 1 spindle shaft, 2 spindle shaft bushes, 1 throttle disc, 2 throttle disc screws, 1 fuel bowl needle and seat, 1 main jet, 2 choke operating rod clips, 1 fuel bowl gasket, 1 carby to manifold gasket, 1 horn gasket Price:
Mini SU carby overhaul kit, suits 1&1/2! What you get: 1 spindle shaft, 1 spindle shaft bushes, 1 throttle disc, 2 throttle disc screws, 1 fuel bowl needle and seat, 1 main jet, 2 choke operating rod clips, 1 fuel bowl gasket, 1 carby to manifold gasket, 1 horn gasket Price:
Mini SU carby overhaul kit, suits 1&3/4 (not HIF44) What you get: 1 spindle shaft, 1 spindle shaft bushes, 1 throttle disc, 2 throttle disc screws, 1 fuel bowl needle and seat, 1 main jet, 2 choke operating rod clips, 1 fuel bowl gasket, 1 carby to manifold gasket, 1 horn gasket & a few assorted washers Price:
Mini SU carby overhaul kit, suits HIF44 What you get: 1 spindle shaft, 1 spindle shaft bushes, 1 throttle disc, 2 throttle disc screws, 1 fuel bowl needle and seat, 1 main jet, fuel bowl seal, 1 carby to manifold gasket, 1 horn gasket & a few assorted washers & rubbers Price:
AIR BOX- Cooper S twin 1-1/4 air box This is a plastic replica of the original cooper S air box. Price:
C-AHT770 Mini water heated manifold, A must for anyone who wants to fit extractors, this manifold will heat up the aluminium manifold to allow better fuel atomisation, (the standard manifold was mounted to the exhaust headers. Will fit 1-1/2, 1-3/4, HIF38 & HIF44 Price:
C-AEG488- MANIFOLD TWIN INLET HS2 ONLY Cast alloy type, this intake manifold for twin SU’s (H2, HS2 or H4 -- NOT HS4) It has been carefully produced to minimize cross-port-flow interference caused by the balance tube and has generous radii in all the right places. Price:
C-AEG489- 1-1/2" inlet manifold (twin carb models) Mini inlet manifold, these are required when fitting twin 1-1/2 carbys to your mini, this manifold has a 'take off' for the booster (on S models) and are made entirly of alloy. Price:
12H1405- Servo fitting for the booster outlet on twin carby mainfold This is a fitting that screws into the twin carby manifold, it allows you to feed in your servo. this will not suit the C-AHT770 single manifold (different thread) Price:
MSSK009- TWIN CARB LINKAGE KIT, SUITS EITHER 1.25” OR 1.5” This fitting kit suits all later day 1.25" and 1.5" twin carb set ups where the balance rods between the carbs required are equal length(2.25"),some early carbs had the balance bar with a triangular plate that were a shorter length. The kit has the original type abutment bracket that fits to the inlet manifold to guide the accelerator cable. Price:
Mini twin 1-1/4 heatshields Mini heat shield made to original specs, this heatshield fits twin 1-1/4 carby setups, paint it your own colour or we can paint it black for you Price:
MSSK1005- HEAT SHIELD STAINLESS STEEL KIT HS2 (1-1/4) TWIN CARBS Stainless steel twin HS2 (1-1/4) heat shields kit. Comes with link bar ,bolts, nuts and springs. Price:
MSSK1006- HEAT SHIELD STAINLESS STEEL KIT HS4 TWIN CARBS Pair of heatshield brackets and cross bar these are made similar to the original cooper HS2 design but ARE for HS4 (1.5") carbys and include the 3 correct springs that attach to the bridging bar for choke return linkage Price:
HSK112- Mini heatshield (for twin 1.5-1.75") This heatshield will fit twin 1-1/2 carby setups, but the throat of the sheilds can be opened up to fit on the twin 1-3/4 setups Price:
|
 |
.jpg)
