Minisport
HomeSearchView CartShippingContact usPrivacy policyRefundsClients cars


Accessories and gift ideas
BMW MINI parts & wrecking
Body parts and accessories
Books and manuals
Brake Components
Brake Pads and Linings
Cables
Cars 4 Sale
Clutch
Cooling
Driveline
Electrical
Engine parts
Exhaust and manifolds
Filters (Oil-Fuel-Air)
Fuel parts & caps
Gearbox parts
Ignition
Interior
K.A.D. Products
Mags/Wheels/tyres & accessories
Moke gear
Mounts and engine supports
New Products
Rover only Parts
Sale Items
Secondhand parts
Steering components
Suspension Bushes and bump stops
Suspension parts
Tools
Zeemax body kits

Minisport
Current Category
Engine parts > Engine head parts & accessories





Mini manifold nut, Long type (SOLD SINGLE)

Mini manifold nut, Long type (SOLD SINGLE)



Price:







QTY:

        
Manifold washer thick type washer

Manifold washer thick type washer

12A1211- WASHER FOR MANIFOLD THICK TYPE

The intake/exhaust manifold should be secured to the head with brass nuts and these very thick washers. These washers are intended to not only spread the clamping action but the thickness allows them to absorb the heat without deforming! Takes 4 per car.



Price:







QTY:

        
STD cam-followers, suit mini

STD cam-followers, suit mini

These are a set of 8 standard-type cam-followers to suit any mini engine, don't ever risk a freshly ground cam-shaft, always replace the followers.



Price:







QTY:

        
Lightened cam-followers

Lightened cam-followers

C-AEG579 -Cam-follower. Lightened set

A factory stock lifter weighs about 44.00 grams, our high performance lifter weighs only 40.00. In addition, these lifters have an oil drain hole, thus preventing a few grams of oil from collecting. This weight saving translates into better control, higher potential engine revs, longer life, etc.

Price:







QTY:

        
ISKY competition cam-folower set of 8

ISKY competition cam-folower set of 8

Reduced weight, designed to minimise float and jump, normally seen in original cam followers, which ultimately looses power.

Price:







QTY:

        
Mini pushrod for 850/998/1100cc (Sold single)

Mini pushrod for 850/998/1100cc (Sold single)

12A250/2A14- Mini pushrod for 850/998/1100cc (Sold single)

This is the pushrod for the small bore engine (850/998/1100cc) these are shorter then the 1275 Push rods- they measure up at about 21.3cm (compared to the 1275 ones at 22cm)



Price:







QTY:

        
Mini pushrod for 850/998/1100cc (Set of 8)

Mini pushrod for 850/998/1100cc (Set of 8)

12A250/2A14- Mini pushrod for 850/998/1100cc (Set of 8)

This is the pushrod for the small bore engine (850/998/1100cc) these are shorter then the 1275 Push rods- they measure up at about 21.3cm (compared to the 1275 ones at 22cm)



Price:







QTY:

        
Mini pushrod for 1275 engine (Sold single)

Mini pushrod for 1275 engine (Sold single)

AEG314MS- PUSH ROD 1275

 

The narrow body of the rod allows for a very high lift cam without fouling the pushrod holes of the cylinder head. need 8 per engine (sold single)- these are longer than the 998/1100cc pushrods.



Price:







QTY:

        
Mini pushrod for 1275 engine (Set of 8)

Mini pushrod for 1275 engine (Set of 8)

AEG314MS- PUSH ROD 1275 (set of 8)

 

The narrow body of the rod allows for a very high lift cam without fouling the pushrod holes of the cylinder head. need 8 per engine (sold as a set of 8)- these are longer than the 998/1100cc pushrods.



Price:







QTY:

        
Valve-guides (STD) iron type

Valve-guides (STD) iron type

12G1963

These are IRON guides that are "bullet shaped" for better flow characteristics, these have a double-lip which accept the ADU4905 (stem seals)



Price:







QTY:

        
Valve-guide set of 8 (Manganese)

Valve-guide set of 8 (Manganese)

C-AJJ4037- MINI VALVE GUIDE SET(8) MANGONESE BRONZE TYPE

A must for any competition car! Although Silicon bronze valve guides were used for their extremely good wear values, they were very hard and not user friendly when fitting. Were possible we now use the Manganese bronze guides which have good cutting properties and good wear characteristics and are original equipment on Porsche and Mercedes.



Price:







QTY:

        
Mini alloy rocker-cover with cap

Mini alloy rocker-cover with cap

Alloy Rocker cover to fit the mighty Mini, this item will make the dullest engine bay look fantastic. This item is "brand new" and will fit all minis.

COMES WITH A CAP, (unlike our competitor's).

 



Price:







QTY:

        
Mini Rocker cover kit, comes with everything to BLING up your rocker cover

Mini Rocker cover kit, comes with everything to BLING up your rocker cover

Rocker cover kit

Dress up your mini under bonnet, this kit is everything to make the first thing you see (rocker cover) jump out at you.

What you get: Rocker cover, T-Bar kit, Rocker cover gasket, and rocker cover sealing grommets.



Price:







QTY:

        
Mini alloy rocker cover cap in RED

Mini alloy rocker cover cap in RED

FP26RED-ROCKER COVER STOVE ENAMELED RED FP26 ROCKER COVER

Great looking and fits all A-Series models! Bolting on an aluminum valve cover is the age-old way to dress up the engine compartment on any car! Also dampens engine valve train noise and will fit twin point cars but can be close to metal water pipe which can be bent away.



Price:







QTY:

        
Mini red alloy rocker cover kit

Mini red alloy rocker cover kit

FP26REDKIT- Red rocker cover kit (with Tbars/grommets and gaskets)



Price:







QTY:

        

Previous Page 1 [2] 3 4 Next Page