Current Category
Suspension parts

This is your suspension page for everything you will require for your mini.

	Mini thick flat washer for tie bar (sold single - 2 per car) PWZ207- Mini thick washer, for tie bar This flat thick waher sits against the cup washer (2A4328) that stops the tie bar from pulling out of the subframe.		Price:	QTY:

	Mini washer for tie bar, cup (sold single- 2 req per car) 2A4328- Mini cup washer for tie bar This cup washer sits against the tie bar suspension rubber, you also require the thick washer aswell (PWZ207)		Price:	QTY:

	Mini rear subframe to body spacing shim (0.020") sold single CK18- RADIUS ARM TRACKING SHIMS IN S/STEEL Specially manufactured shim washers to alter tracking. Manufactured in 0.020” stainless steel they are inserted between the vertical face of the outer radius arm bracket and the sub-frame. These shims give permanent settings and ultimate strength, yet can easily be added/removed as required.		Price:	QTY:

	Pair of ball joints (Top and bottom) PAIR OF BALL JOINTS- GSJ166MS Ball joints to fit any disc or drum brake hub!		Price:	QTY:

	Mini metro ball joint (Single) GSJ268- 'ROVER' METRO BALLJOINT >84 This is a single ball joint, completely assembled, with plastic boot, for Metro swivel hubs only up to 1984. If using metro hubs on mini,this is the balljoint to use. it has the same taper as mini.		Price:	QTY:

	Mini ball joint boot, stop dirt from damaging ball joint- BTA377 BTA377- Mini ball joint boot This is a dust cover/boot for either your top or lower ball joint on either drum or disc brake cars.		Price:	QTY:

	Mini ball joint lock tab 2A4238- Mini ball joint locktab This is the locktab that fits under the ball joint nut on the front of any mini, it suits either drum or disc brakes		Price:	QTY:

	Mini ball and cup, fits the top arm and rear trailing arm 21A1163- SUSPENSION KNUCKLE JOINT These joints are complete with the knuckle, nylon cup (21A423) and rubber boot (21A425). If your suspension has dropped suddenly, or you have loud squeaking noise during suspension movement, then these knuckles are one of the first things you should check.		Price:	QTY:

	Pair of ball and cups for your top or rear trailing arms) PAIR OF BALL AND CUPS- 21A1163 Ball and cups can wear through the nylon cup and constantly squeak every time you go over a bump, these fit either hydro or rubber cars.  21A1163- Minispares Catalogue 2005, page number 2, item 2.a		Price:	QTY:

	Ball and cups, Set of 4 to suit Mini 21A1163 Mini ball and cups quite commonly wear through the cup and damages the ball, this then gives you a annoying squeak, as metal rubs against metal. SET OF 4		Price:	QTY:

	Mini suspension nylon cup (part of the ball and cup) 21A423- SUSPENSION KNUCKLE JOINT NYLON CUP ONLY If your ball is ok and you just want to replace the cup then this is all you need.		Price:	QTY:

	Upper arm repair kit, all models (one side) Mini Upper Arm repair kit This Mini Upper Arm repair kit is for the top arm on the suspension on the front of any mini or moke.		Price:	QTY:

	Rear trailing arm repair kit for mini (not moke-see below) Rear Trailing Arm Kit You are bidding on a rear trailing arm repair kit for MINI's and MOKES, this kit has all you will need to replace a bent trailing arm/or worn out trailing arm. *Please note that new bush (supplied) in trailing arm may require reaming out after intallation (wont cost you much).		Price:	QTY:

	Rear trailing arm repair kit for moke (not mini- see above) Moke Rear Trailing Arm Kit Rear trailing arm repair kit for MOKES, this kit has all you will need to replace a bent trailing arm/or worn out trailing arm. these have the bearings on either end (not like the mini which has a bush on the other end)		Price:	QTY:

	Mini dust excluder for rear trailing arm and upper arm 2A7327-SEAL DUST EXCLUDER RADIUS/UPPER ARM Round rubber seal which acts as a dust/debris excluder on the rear radius arm and front upper arms		Price:	QTY:

[1] 2 3 4 Next Page