Minisport
|
Minisport |
 
|
HMP441015- REAR QTR PANEL LOWER L/H Suit Rover Genuine heritage british part, The rear quarter outer skin from the B post back From below the rear side window down. Left hand and does not include the inner stifener waist rail. suit rover Extra freight charges will apply Price:
BMP127MS –LEFT OR RIGHT, SEAM MOULDING FRONT NOT PRIMED This is our own best selling aftermarket seam molding. These are the vertical moldings that protect the 4 body corner seams. Price:
BMP124MS- SEAM FINISHER R/H REAR SEAM NOT PRIMED Quality Aftermarket Body Seam Covers. These are the vertical ones that protect the 4 corners of your cars body seams. Price:
BMP125MS- SEAM MOULING L/H/ REAR SEAM NOT PRIMED Quality Aftermarket Body Seam Covers. These are the vertical ones on each corner of your car to cover and protect the body seams. Price:
BMP128MS- SEAM MOULDING CLIP STAINLESS STEEL, ANTI RUST These are the clips that hold on the vertical seam mouldings on all minis. The original metal type are prone to rust so Mini spares producedd these stainless steel versions (28 required for a full car, 7 clips per corner) Price:
K.A.D round nose bonnet One of the problems with the round nose car is that when fitting anything other than the normal components there is not much room, you can solve that easily with this bonnet, designed especially with the KAD twin cam in mind, this bonnet will allow a lot of extra room for anything you may like to shove under it. Price:
14A6468- NUMBER PLATE BRACKET REAR MK1 850 (larger type) The MKI (850 sliding window) number plate panels are hinged at the top to swing out clear of the bumper when you open the boot lid. Price:
14A6466- NUMBER PLATE HINGE R/H MK1/2 The MKI & MKII number plate panels 14A6468 are hinged at the top to allow you to keep your boot open while you drive along, this keeps the numberplate visable at all times. Price:
14A6467- NUMBER PLATE HINGE L/H MK1/2 The MKI & MKII number plate panels 14A6468 are hinged at the top to allow you to keep your boot open while you drive along, this keeps the numberplate visable at all times. Price:
211081- MINI BOOT FLAP SCREW 3/16 (also can be used on Australian door strikers) This is a boot flap screw that holds the boot flap hinge onto the car, there are 6 of these required per car. the thread is 3/16th of an Inch. these screws can be used on the australian door strikers HYA2805 (you will need to run a 3/16 tap) Price:
MS16R- DOOR STEP SHAPED PANEL MK3 RH These door step panels actually have the start of the curves at the end where they are able to rust. This is the Right hand side, see MS16L for left hand. You can cut the straight sections out to use as repair sections on sliding window/Australian windup window type door frames MK1/2 as the profile is the same. Price:
MS16L- DOOR STEP SHAPED PANEL MK3 LH These door step panels actually have the start of the curves at the end where they are able to rust. This is the Left hand side, see MS16R for right hand. You can cut the straight sections out to use as repair sections on sliding window/Australian windup window type door frames MK1/2 as the profile is the same. Price:
MS23- VALANCE CENTRE APRON VAN & ESTATE Non genuine rear valance for vans/estates. pick-ups The rear lower center section only of the valance-the 2 corners are separate parts MS52R and MS52L Price:
BMP130- SEAM MOULDING REAR VALANCE VAN/ESTATE/PICKUP The horizontal moulding that fits along the top of the rear valance under the doors of estates, pickups and vans. For the corner mouldings see BMP131 Price:
MS52R- VALANCE APRON CORNER R/H VAN AND ESTATE The rear lower non genuine corner section of the rear valance on vans.estates.travellers and pick ups R/H---See MS23 for centre section Price:
|
 |
