Current Category
Mounts and engine supports

	Mini Exhaust mount for the rear (ultra strong) EXHAUST MOUNT- Rear heavy duty exhaust mount This exhaust mount goes on the Very rear of the subframe, you could use this elsewhere		Price:	QTY:

	Gearchange mount (remote type) 21A956 This is the mount at the very rear of the gear-change on remote gear-change (not rod or 850)		Price:	QTY:

	Firewall bracket, radiator end BYK2164- Firewall secondary engine steady bar bracket Bracket that fits on your firewall bulkhead, this is connected to the engine steady on rod change/high performance motors. (Radiator side) and has holes for heater pipes to go through firewall.		Price:	QTY:

	Radiator staybilizer bracket 1000-1100cc head AYK2076- Stabilizer bracket cylinder head end suit 1000-1100cc (Thermostat) For use on all 1000cc to 1100cc engines, A must for engines fitted with rod change. For 1000/1100cc not 1275 these are available in our store.		Price:	QTY:

	Radiator staybilizer bracket 1275 head Stabilizer bracket cylinder head end suit 1275 (Thermostat) For use on all 1275 engines, A must for engines fitted with rod change. For 1275 only not 1000/1100cc these are available in our store.		Price:	QTY:

	Mini engine steady bush kit (rubber)- (4 bushes) 2A5875 (x4)- Mini engine steady bush kit (rubber) This is 4 bushes (enough for one side) for your engine steady bush/bar.		Price:	QTY:

	Mini engine steady bush kit (polyurethane) C-STR630- STABILISER BUSH POLYURETHANE ENGINE KIT A "must have" for every car! All the torque action of the motor is controlled by the stabilizer arm located just above the flywheel housing. If you are still using original-type rubber bushes you are living in the past!		Price:	QTY:

	Mini engine steady bar 'HARD' bush kit (poly) RACE C-STR630RACE- STABILISER BUSH HARD POLYURETHANE ENGINE KIT A "must have" for every car! All the torque action of the motor is controlled by the stabilizer arm located just above the flywheel housing. If you are still using original-type rubber bushes you are living in the past! THESE ARE EXTRA HARD FOR COMPETITION OR WHERE ENGINE TRANSMITTED NOISES ARE NOT A PROBLEM. USE C-STR630 IF YOU WANT QUIET BUSHES THAT DO NOT TRANSMIT NOISE		Price:	QTY:

	Mini staybar inner metal bush Mini engine stabilizer bush This bush fits inside the engine stay bar rubbers/poly mounts; quite often they rust up or are damaged. Will fit ALL top engine ‘dog bone’ stay bars		Price:	QTY:

	Mini front subframe mount (fits the late type) does not fit solid mounted subframes 21A2624- SUBFRAME MOUNTING FRONT OF THE FRONT SUBFRAME 2 of these rubber mountings are fitted at the front of the front sub-frame on all vehicles from (mk4) on, Also required when fitting new type rubber mounted clubman aprons. Genuine rover item		Price:	QTY:

	Mini front subframe, rear mount, genuine (sold single, 2 required) 21A2599- SUBFRAME MOUNTING FOR REAR OF THE FRONT FRAME,GENUINE Priced each, 2 of these are fitted to the rear of the front subframe on all cars from 1976 on. These are original genuine rubber type		Price:	QTY:

	Mini engine stabiliser bush, one piece, fitted to MPI rovers (Sold single) KKF101320- STABILISER BUSH ONE PIECE 1996on MPI UPPER STABILISER BAR The last Rover update on the upper engine stabilizer bar. A one piece silent block type bush was fitted at both ends from 19996 on and will fit any cars that had 2 bushes fitted at either end as original. These have also been fitted to the lower engine stabilizer bars on the gearbox by some mini enthusiasts.		Price:	QTY:

	Morris 1100 radiator engine support mounts, QH brand 2A305- Morris 1100 engine mount/s We know a few of our clients have morris 1100 cars, (NOT MIINI) these are the mounts that go on the radiator end of the engine		Price:	QTY:

Previous Page 1 [2]