Minisport
|
Minisport |
 
|
ACH6001- Steering column nut 1-5/16" This is the column nut as used on all models of minis ever released here. This nut is NOS but has NEVER been used. It requires 1-5/16" socket. This nut holds the steering wheel onto your column Price:
CCA45- Mini Rack pinion load washer (wave washer) This is a steering rack pinion wave washer, there are two of these that hold a preset tension against your pinion (load) if one of these are broken it can make the steering a bit loose- the washers sit in opposing each other. Like this ")(" Price:
2A4315- Mini steering arm bolt- sold single There are 2 of these bolts per arm and the locating rings for them in the hub are FAM6924 and the locktab are 2K5377 and all of these parts were standard fitment on every mini produced. Torque setting 30 to 35 lb/ft Price:
FAM6924- MINI STEERING ARM DOWEL the dowel that fits in the front hub to locate the steering arms. Bolts for these are 2A4315 and the locktabs are 2K5377 Price:
BTA894RH- STEERING ARM R/H MK II "S" upgrade on Mk2 on Upgraded thicker steering arm as fitted to Cooper S MK2/3 and 1275GT. The Mini MK2 Steering arms were designed to be used with the later model rack that has a tighter turning ratio than the early MK1 rack. The angle of these arms is slightly different thus allowing the tie rod end to have a little more range of adjustment into the rack. These can be used on any mini from 1967 MK2 on as an upgrade but should be used in pairs Price:
BTA895LH- STEERING ARM L/H MK2/3 "S" upgrade on Mk2 on Upgraded thicker type arm as used on Cooper S Mk2/3 and 1275GT. The Mini MK2 Steering arms were designed to be used with the later model rack that has a tighter turning ratio than the early MK1 rack. The angle of these arms is slightly different thus allowing the tie rod end to have a little more range of adjustment into the rack. these can be fitted to any car but must be fitted in pairs Price:
2K5377- STEERING ARM LOCKTAB- PLATED Locktab for under the steering arm bolts on all minis-fits either side Price:
This is for use on all models (most suited to Morris) and will enable you to lower the steering column; this gives you the choice of where you like the steering wheel to sit. Easy to fit! Price:
GSJ734MS- MINI & MOKE STANDARD TIE ROD END This tie rod end is fits on the end of your steering rack, don't play around with dangerous suspension parts, replace them fast. Price:
C-AJJ1572- TRACK ROD END LONGER TYPE Extra long for use on a lowered Mini with negative camber. What these give you is more thread inside the tie rod end, this keeps your suspension A LOT safer when fitting a front end adjustable kit. Price:
21A30- Mini steering rack to body seal (foam felt) This seal stops water and noise from entering where the steering rack pinion comes through the body on all models. Price:
FAM7306- Mini or moke steering rack ALL New steering rack for Mk1&2 models on with right hand drive steering, New tooling has resulted in an even stronger rack, this will also fit mokes. Price:
2A6208- MINI STEERING RACK U BOLT Special shaped U bolt for holding the steering rack in place. Every mini uses 2 of these. Price:
C-AJJ1570- STEERING RACK 2.2 TURN QUICKRACK RHD BRAND NEW If you are interested in performance driving then you know reaction time from the driver to the car is critical; the time it takes to turn the steering wheel to the desired angle is important! The standard rack is 2.7 turns lock to lock, our quick ratio is 2.2 turns! AFTER 5 years off the market these have just been remade, only a few in stock! Price:
BHM7113- Mini rack boot set (budget) These are a pair (you get two) rack boots to suit a mini STD steering rack. Price:
|
 |
